Infrared Resources External Universal IR Receiver Extender for VERIZON FIOS, SA/Cisco Explorer, Comcast, Samsung,PACE,Motorola,Arris,

Infrared Resources External Universal IR Receiver Extender for

Designed and sold Exclusively by Infrared Resources.Designed in the USA. 9 feet long with 3.5mm end plug. IR receiver is 38~56kHz This compact (.53 x 1.12 × .43 ) 1/2 inch wide, 1 inch long and 1/2 inch tall. IR Receiver truly is universal. It works with ALL of the major Cable Set Top and DTA (Digital Transport Adapter) Boxes. Including VERIZON FiOS, Comcast, S/A Scientific Atlanta Explorer ,Except the box models listed below in the Will Not Work list. Allows you to hide your equipment and operate the equipment remotely. Simple plug and play. Unplug the power from the cable box then plug the IR receiver into the IR IN port. Plug in the power for the box. NOTE: Not for use in TV (Smart) IR port. The IR port on TV monitors are IR OUT not IR IN The front IR sensor on the Cable box will disable once the IR receiver is plugged in. RNG models front IR sensor does not disable. Works With: Samsung STB SMT-H4372,Scientific Atlanta Explorer 46xxHDC Series, 9865HDC,8742HDC Explorer (with IR IN port on the back panel) Comcast X1 RNG Set Top Boxes VERIZION HD DVR QIP 7xxx series and VM1101 model Cisco CHS435HDC,CH335HDC HD DVR, LG LST-4600A HD PACE DC551P,DC55 PACE/ DC700X Apache. Comcast X1, RNG110, PACE/CiscoRNG150, RNG100, PACE TDC787X HD, PACE TDC 575D DVR, DC50X, DCH100, DCX3300, DCX3...

  • Brand: Infrared Resources
  • ASIN: B0107LT77S
  • UPC: 804879557746

6-Feet 37.9KHz External IR Receiver Cable, Infrared Receiver for TV sets, STB,Satellite receivers etc(IRR-102)

6-Feet 37.9KHz External IR Receiver Cable, Infrared Receiver

IR(Infrared) Receiver Extender cable which is a IR receiver and a plug are connected with a wire, in order to conveniently realize the receiving and amplifying the infrared remote controller signal.The type of IR receiver's epoxy package and the shell can filter the visual interference. The demodulated output signal can directly be decoded by a microprocessor. It may be used in STB, Video recorder,DVD,DVR,PVR,satellite receivers, etc. Specification: Carrier Frequency: 37.9KHz Rec. Operating Voltage: 2.7~5.5 Vcc, 1.2mA Icc Typical. VOH: 0.25Min, 5.0 Max. Receiving Distance: 20m Typical Horizontal Half Angle 45 Degree Operation Temp.: -25~+85 Celsius Degree Storage Temp.: -25~+85 Celsius Degree Precautions for use:Disconnect power before connecting IR Receiver.Make sure your 3.5mm port is for input, not output BE NOTED Our IR works for Directv H25,Telus Cisco IPV6015,CISCO IPV-6016, Cisco IPV5050,EPB fiber box Our IR Doesn't work for DTA 50,70,170,270. Cisco4640/4642HD,4740/4742HD,CHS435HDC,CHS335HDC,Verizon QIP2500,2708,6416,6200,Motorola VIP12xx,19xx. ALL Onkyo Recivers,harman kardon avr

  • Brand: SR Technology
  • ASIN: B01BY19HH0
  • UPC: 600682469555

Infrared Resources 9ft 38-56kHz Dual Band External Universal IR Receiver Extender for Verizon FiOS + Most Cable Boxes and DTA Units.

Infrared Resources 9ft 38-56kHz Dual Band External Universal

Infrared External Receiver for Verizon FiOS cable boxes. Simple plug and play. Plugs directly into the IR IN port on the back of the cable box It will work with QIP7000 series, VMS1100, IPC1100,CHS335,CHS435, DTA271, DTA50 etc Will not work. QIP2500 or QIP6000 series, SA 4000HDC series,4200/HDC,4240,4250/HDC,8300/HD,8240/8260HDC box , IR Repeater kits, or TV sets. Copyright 2017 Infrared Resources LLC All rights reserved

  • Brand: Infrared Resources
  • ASIN: B002JSDHCY
  • UPC: 845456004468

Inteset 38 kHz Infrared Receiver Extender Cable for HD DVR's & STB's- Check Compatibility

Inteset 38 kHz Infrared Receiver Extender Cable for

This 38 kHz IR Receiver is sold exclusively by Inteset. No other Vendors sell or ship the same extender. It has been built with the highest quality materials available.There is no better receiver from any competitor at any price. This allows you to hide your cable set top box behind closed doors in a cabinet or closet. The small receiver bud (7/8" x 15/16") will handle all of the same functions as if your set top box was out in the open. It is made to work with nearly all 38 kHz Set Top Boxes (STB) that have a 3.5 mini IR jack in the back of the device. It comes with self stick tape on the back of the IR bud for easy installation on any flat surface. Be sure to mount the bud with a straight line-of-sight to your remote. Below are some of the devices that are confirmed to work with this receiver. It will work with Comcast X1 & RNG150(Cisco), Verizon HD DVR QIP all QIP 7xxx series, Arris VMS & IPC1100, Pace TDC787X HD, PACE TDC575D DVR, DC50X, DCH100, DCX3200, DCX3300, DCX3220c/e, DCX3400-M, DCX3416, DCX3425, DCX3432, DCX3501, DCX 3501-M, DCX3510-M, DCX3520, DCX 3635, DCX700, RNG100, RNG110, RNG150, RNG200N, Cisco CHS435-HDC, CH335-HDC HD DVR, Channel Master DVR, LG LST-4600A, Thomson DCI1011com, Samsung sr150bnm It will not work with most Scientific Atlanta/Arris boxes, Motorol...

  • Brand: Inteset
  • ASIN: B00YFC2IQ8
  • UPC: 791102616687

Monoprice 5 feet IR Extender Cable/Receiver, Black (8060)

Monoprice 5 feet IR Extender Cable/Receiver, Black

This IR Receiver Extender cable is a receiver device for use with infrared remote controls. It plugs into a source device or IR extender and serves as the IR sensor for remote control input. It is compatible with the HDMI ; extender wall plates from Monoprice, PIDs 8008 and 8201 . Support Files: User s Manual HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

  • Color: Black
  • Brand: Monoprice
  • ASIN: B005E2XLNM
  • UPC: 641125082078

Inteset IReTV USB IR Receiver for use with Nvidia Shield (2nd Gen), F-TV, Kodi, PCs, Raspberry Pi & Other Streamers with The Inteset INT422 & Harmony Remotes (Remote not Included)

Inteset IReTV USB IR Receiver for use with

The IReTV USB IR Receiver is designed and built to work with Fire TV (Some versions require a USB Y Cable), Nvidia Shield-2nd Generation consoles (1st Gen and Pro versions do not require an add-on IR receiver), Media Center and MCE related apps as well as Kodi on a PC and Kodi on Raspberry Pi. This IR Receiver works only with Inteset INT422-3 & Harmony remotes (Remote NOT included).Some older INT422-3 remotes will need to be updated to control Fire TV. Contact us to update your remote free of charge.To install the IReTV IR Receiver using the INT422-3 remote, just plug the USB connector into the port on the device you want to control and enter the Device Code for that device in one of the available Device Code buttons (A, B, C, D) at the top of the remote. You can then use the other device buttons for your TV, Cable box etc. We have provided a Key Map for these devices above or you can view the map on our web site. The INT422-3 Device Codes are: 02049 (Fire TV), 01272 (Media Center), 02000 & 01272 (Kodi on a PC & Kodi on Raspberry Pi) and 04918 (Nvidia Shield). The set-up process and the Key Mapping for the Logitech Harmony Remote is available at our web site. Currently, only Fire TV and Nvidia Shield (2nd Gen) are controllable using the Harmony remote with the IReTV Receiver. Oth...

  • Brand: Inteset
  • ASIN: B077MRD2P4
  • UPC: 711583700873

Inteset 38-56 kHz Wideband Infrared (IR) Receiver Extender Cable for Cable Boxes, DVR's & STB's. Check Compatibility.

Inteset 38-56 kHz Wideband Infrared (IR) Receiver Extender

This newly designed 38-56 kHz Wideband STB IR Receiver Extender is made and sold exclusively by Inteset Technologies. It will work with nearly all Cable Set Top Boxes and DVRs that have an active IR IN port. Previously you had to choose either the 38 kHz or the 56 kHz model. This product eliminates having to make that choice but it will not work with all A/V devices. Please check compatibility below.This allows you to hide your STBs and DVRs behind closed doors in a cabinet or closet. The small receiver bud (1 1/4"L x 7/8"W x 5/8"H) will handle all of the same functions as if your device was out in the open. It comes with self stick tape on the back of the IR bud for easy installation. Be sure to mount the bud with a straight line-of-sight to your remote. It will work with most Comcast Xfinity and Verizon FIOS boxes as well as other cable providers that use Arris, Cisco, Scientific Atlanta and Motorola boxes except those noted below.It will NOT WORK with AT&T Uverse STBs, Motorola DCT or DCH Series, QIP2500, QIP6000 Series, DISH or DirectTV boxes. These models and some models specific to particular cable providers either do not have an IR IN port or that port is not active. The 4250 HDC is one of those. It also will NOT WORK with A/V Receivers, Amplifiers, TVs or IR Repeater Syst...

  • Brand: Inteset
  • ASIN: B01LXO79CL
  • UPC: 722512375956

Inteset USB External Infrared (IR) Kodi & Media Center Receiver with Cable for use with MCE and other Universal Remotes (Not the same as IReTV IR Receiver)

Inteset USB External Infrared (IR) Kodi & Media

This custom IR Receiver is connected to any USB 2.0 external connector on your computer with the cable provided and is ready to go. It is for use with media applications only. The outer casing of the receiver is so small (1 1/4"L x 7/8"W x 5/8"H) that it can be mounted almost anywhere with the included double stick tape. The cable is 60" long so that you can have your computer in a cabinet and put the receiver on a shelf. This Receiver can be used with any RC6 Protocol Remote including our INT422 Universal Remote. This Receiver is not for use with the Xbox One.The eHome drivers will load automatically when the USB plug is inserted in the computer's USB connector on W7 & W8. You will have to load the eHome drivers for W10. Be sure that your Device Manager shows the eHome drivers loaded under Human Interface Devices as well as Universal Serial Bus Controllers as shown in the screen shot above. If you remove the USB plug from the computer the two eHome listings should disappear. If you have any issues, remove the plug and re-insert it. You can contact us at: http://universalremotes.net/.

  • Brand: Inteset
  • ASIN: B00J5NRWFO

6' Dual Mode Infrared IR Remote Control Target Eye Receiver Extension Extender Cable 38/56 kHz Universal for Comcast Xfinity and other DTA STB

6' Dual Mode Infrared IR Remote Control Target

NOTE: YOUR DEVICE MUST HAVE A 3.5mm IR JACK Insert IR Extension Cable while device is powered OFF This IR Target Extension is designed and built with the highest quality materials to work flawlessly with both 38 kHz and 56 kHz IR Remote standards. The IR Target Extension allows you to hide your cable TV STB (set top box) or DTA (digital transfer adapter) behind your TV. Aim your Remote at the small IR receiver and it transfers signals from your remote directly to the attached cable box. It comes with 3M double-sided mounting tape to attach to any flat surface visible to your remote control. COMPATIBILITY: It will work with most devices with 3.5mm IR Input mini-jack in the back of the device, including... Most Set Top Boxes (STB) Most Digital Transfer Adapters (DTA) Many Digital Video Recorders (DVR)

  • Brand: NSI
  • ASIN: B076QMDLKN
  • UPC: 685784665937

Inteset 56 kHz Infrared Receiver Extender for Scientific Atlanta, Arris, Cisco Explorer and Other Cable Set Top Boxes (STB)

Inteset 56 kHz Infrared Receiver Extender for Scientific

This 56 kHz IR Receiver is made by the largest supplier of set top remotes in the world and sold exclusively by Inteset Technologies on Amazon. It has been designed and built to work flawlessly with the highest quality materials available. There is no better quality receiver from any competitor anywhere. This IR Receiver Extender allows you to hide your cable set top box behind closed doors in a cabinet or closet allowing a very clean installation. The small receiver bud (7/8" x 15/16") will handle all of the same functions as if your set top box was out in the open. It is made to work with nearly all 56kHz Set Top Boxes (STB) and Digital Video Recorders (DVR) that have an active 3.5 mini IR jack in the back of the device. It comes with self stick tape on the back of the IR bud for easy installation on any flat surface. Be sure to mount the bud with a straight line-of-sight to your remote. Below are some of the devices that are confirmed to work with this receiver. PLEASE CHECK THE BACK OF YOUR DEVICE TO BE SURE THAT YOU HAVE A 3.5 MINI INPUT JACKWILL Work with: Arris including: DCX3200/3600-M(Not All), Scientific Atlanta/Cisco Explorer/Arris including: DTA 50, 170, 270, 1640/1642HDC, 4640/4642HDC, 4740/4742HDC, 8640/8642HDC, 9865HDC(Not All) Will NOT Work With: AT&T Uverse STB,...

  • Brand: Inteset
  • ASIN: B0155FNLZK
  • UPC: 791102616724

TNP Infrared Receiver Extender Cable 10FT - 38-56kHz Dual Band IR Sensor External Universal IR Receiver Extender Connector Extension Cord Wire Plug for Verizon FiOS, Arris, STB

TNP Infrared Receiver Extender Cable 10FT - 38-56kHz

This 38-56kHz IR receiver extend the IR signal received from the remote control and relay via the wire to the equipment (cable box, set top boxes, etc...) connected to it. You may now hide your cable box or component inside your entertainment center system cabinet, closet, behind a closed door and still able to be control it with your IR remote control.Specification:Will NOT work with Will NOT work with SA 4000HDC series, 4200/HDC, 4240,4250/HDC,8300/HD, 8240/8260HDC box, Uverse or A/V Receivers,IR Repeater kits, or port on the back of any box stating Serial. It is for data and technicians useWill NOT work with most Scientific Atlanta/Arris boxes, Motorola DCT or DCH, Series, QIP2500, SA Explorer 4280 HDC, 8300HD, Cisco DTA 30, 50, 1642HDC, 8742HDC, 9865HDC, Verizon Motorola QIP 6416-2 , 6000 series, Motorola/Arris DCX3200-M,DCX3400, DCX3600, DCX3600-M, RNG200. DISH, Direct TV. Will not work with any STB without an active 3.5 IR IN Port, A/V Receivers, TVs or IR Repeater SystemsCompatible with Comcast X1 & RNG150 (Cisco), Verizon FIOS HD DVR QIP all QIP 7xxx series, Arris VMS & IPC1100, Pace TDC787X HD, PACE TDC575D DVR, DC50X, DCH100, DCX3200, DCX3300, DCX3220c/e, DCX3400-M, DCX3416, DCX3425, DCX3432, DCX3501, DCX 3501-M, DCX3510-M, DCX3520, DCX 3635, DCX700, RNG100, RNG110, RNG...

  • Brand: TNP Products
  • ASIN: B07R6YWP9C
  • UPC: 843354106666

TNP Infrared Receiver Extender Cable 10FT - 38-56kHz Dual Band IR Sensor External Universal IR Receiver Extender Connector Extension Cord Wire Plug for IR Repeater Systems

TNP Infrared Receiver Extender Cable 10FT - 38-56kHz

This 38-56kHz IR receiver extend the IR signal received from the remote control and relay via the wire to the equipment (cable box, set top boxes, etc...) connected to it. You may now hide your cable box or component inside your entertainment center system cabinet, closet, behind a closed door and still able to be control it with your IR remote control.Package Content:1x Infrared Receiver Extender Cable 10FT - 38-56kHz Dual Band IR Sensor External Universal IR Receiver Extender Connector Extension Cord Wire Plug for IR Repeater Systems

  • Brand: TNP Products
  • ASIN: B07RBCRVLV
  • UPC: 843354106673

TNP IR Repeater Extender - Mini USB Powered Dongle Universal Infrared IR Remote Control Extender System with IR Receiver, IR Transmitter, and IR Blaster Emitter Booster Extension Cable

TNP IR Repeater Extender - Mini USB Powered

Do you want to control audio and video devices like AV receiver, DVD Blu-ray player, and satellite receiver set top box STB etc, that are located in another room or inside your AV component cabinet? Are you tired of leaving the cabinet door open so your remote can operate your devices? Why try to hide an old large antiquated bulky transmitter behind your ultra-thin TV. Our mini USB powered IR extender repeater dongle is easy to install with ultra compact design.This remote control transmitter and receiver system kit allows you to control devices through walls, doors, ceilings, floors, etc... with no direct line-of-sight needed. It even works through closet door and closed entertainment system cabinet.Specification:You can set the Transmitter out near the TV and the built-in IR window on it will pick up the signal from your remote and send the command to the IR Receiver that will control your devices.Another setup option is through the wired IR Receiver (included) to pickup the IR signals, this allows you to hide the transmitter behind your TV. So all you have to do is put the small IR receiver in line of sight to your remote. When the IR receiver unit gets the signal from the IR transmitter, the unit has a built in IR blaster that then floods the area with the IR signals.If you n...

  • Brand: TNP Products
  • ASIN: B01MU5RQ1A
  • UPC: 818073023044

TNP IR Receiver Cable - External 38-56kHz Infrared Receiver Extender Sensor Cable 3.5mm Jack Plug Wire Cord Remote Eye for HD DVR Cable Box, STB Set Top Box, TV, IR Repeater Extender (10FT, Black)

TNP IR Receiver Cable - External 38-56kHz Infrared

This 38-56kHz IR receiver extend the IR signal received from the remote control and relay via the wire to the equipment (cable box, set top boxes, etc...) connected to it. You may now hide your cable box or component inside your entertainment center system cabinet, closet, behind a closed door and still able to be control it with your IR remote control.Specification:Length: 10 FeetInstallation steps:1. Locate the IR input jack on the back of the box2. Plug the cable in the IR input jack3. Place the round IR sensor receiver with a direct line of sight from your remote controlNOTE: Please check your device for an active 3.5 mini input port labeled "IR", "IR In" or "IR Input"Package Content:1x IR Receiver Cable - External 38-56kHz Infrared Receiver Extender Sensor Cable 3.5mm Jack Plug Wire Cord Remote Eye for HD DVR Cable Box, STB Set Top Box, TV, IR Repeater Extender System (10FT)

  • Color: Black
  • Brand: TNP Products
  • ASIN: B078M6PCY9
  • UPC: 843354100794

Inteset IR Remote Control Repeater-Extender-Emitter to Control up to 8 Hidden A/V Devices Like Cable Boxes, Xbox One, Roku, Apple TV, Nvidia Shield and Others with Our Powerful IR Receiver

Inteset IR Remote Control Repeater-Extender-Emitter to Control up

With a remote, this IR Repeater allows you to place your AV Receiver, Cable Box, DVR or other devices in a cabinet or in another room and still be able to control them from in front of your TV. Simply place the IR receiver where you wish to aim your remote control (usually the TV), run the IR receiver wire from your TV to the distribution box. Then run the IR emitters to the devices you wish to control and place an emitter over the IR receiver window in each device, plug the 12v DC plug into a wall outlet and your all set! . Just attach the USB Cable from the distribution unit to any working USB connector on any of your devices. The dual band IR Receiver can receive commands from 38 kHz to 56 kHz. The kit includes: • 1 Distribution Unit • 1 IR Receiver • 1 12v DC power plug • 4 Dual IR Emitters to control up to 8 devices (you can add 2 more dual IR emitters to control 12 devices) • 1 User Manual Specifications: • The IR receiver cord is 5' long and can be extended with a 3.5mm AV extension cable by up to 50 feet or more • The distribution unit measures approximately 2.25"x 4.5"x 1" and has slots for mounting, if desired (mounting screws NOT included) • The distribution unit can also be powered by a USB cable instead of the 12v adapter. USB Cable is NOT INCLUDED. N...

  • Brand: Inteset
  • ASIN: B010CAJ4AY
  • UPC: 791102616700
Similar External Ir Receiver Results