CONFAST 1/4" x 3" Hammer Drive Nail in Anchor (100 per Box)

CONFAST 1/4" x 3" Hammer Drive Nail in

ApplicationsThe anchor is made from ZAMAC. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Dry environment.Hole Diameter/Bit DiameterThe anchor requires a 1/4" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/4".Length Anchor The length of the anchor is 3"Minimum EmbedmentThe minimum anchor embedment into the concrete is 3/4". Therefore, the anchor must be installed so that a minimum of 3/4" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.

  • Brand: CONFAST
  • ASIN: B071GD77N8

Wej-It Nail-It DN1420 Drive Anchor, Zamac Alloy, Zinc Plated Finish, Meets GSA FFS-325 Group V Type 2 Class 2 Specifications, 1/4" Diameter, 2" Length (Pack Of 100)

Wej-It Nail-It DN1420 Drive Anchor, Zamac Alloy, Zinc

The Wej-It Nail-It DN1420 drive anchor is made of zamac alloy and cold rolled steel, provides a secure hold in concrete, block, brick, and stone, and meets Federal Specification GSA FFS-325 Group V, Type 2, Class 2. The anchor body inserts into a drilled hole and a hammer (sold separately) drives the pin down into the body, expanding the body and gripping the mounting material. The anchor's mushroom head lies above the material surface when installed, and the nail enters the head when installed to create a tamper-resistant seal.SpecificationsAnchor Part NumberDrill DiameterMaximum Thickness of FixtureMinimum Embedment DepthUltimate Tensile Strength of Static Loads in 3,000-psi Unreinforced Stone Aggregate ConcreteDN36783/16"1/4"5/8"400 lb.DN14031/4"1/8"5/8"500 lb.DN14101/4"1/4"3/4"800 lb.DN14111/4"1/2"3/4"800 lb.DN14121/4"3/4"3/4"800 lb.DN14201/4"1-1/4"3/4"800 lb.DN14221/4"1-3/4"3/4"800 lb.DN14301/4"2-1/4"3/4"800 lb.Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). For more information, see the specifications sheet.Anchors provide reinforcement to fasteners installed in materials that are considered brittle or have insufficient hold such as drywall, concrete, brick, and stone. Anchors provide support through method...

  • Brand: Wej-It
  • ASIN: B000BD6DMA
  • UPC: 013918502207

CONFAST 1/4" x 2-1/2" Hammer Drive Nail in Anchor (100 per Box)

CONFAST 1/4" x 2-1/2" Hammer Drive Nail in

ApplicationsThe anchor is made from ZAMAC. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Dry environment.Hole Diameter/Bit DiameterThe anchor requires a 1/4" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/4".Length Anchor The length of the anchor is 2-1/2"Minimum EmbedmentThe minimum anchor embedment into the concrete is 3/4". Therefore, the anchor must be installed so that a minimum of 3/4" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.

  • Brand: CONFAST
  • ASIN: B072QR6XDN

CONFAST 1/4" x 2" Hammer Drive Nail in Anchor (100 per Box)

CONFAST 1/4" x 2" Hammer Drive Nail in

ApplicationsThe anchor is made from ZAMAC. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Dry environment.Hole Diameter/Bit DiameterThe anchor requires a 1/4" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/4".Length Anchor The length of the anchor is 2"Minimum EmbedmentThe minimum anchor embedment into the concrete is 3/4". Therefore, the anchor must be installed so that a minimum of 3/4" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.

  • Brand: CONFAST
  • ASIN: B071GD78DZ

Powers Fastening Innovations 50310 Hammer Drive Setting Tool Standard, 1 Per Box

Powers Fastening Innovations 50310 Hammer Drive Setting Tool

Powers Fasteners is the leading supplier of concrete and masonry anchors in North America and has been a leader in the fastening industry since 1921. Powers is an ISO-9001 international anchoring products company with extensive expertise in the following groups: Mechanical Anchors, Adhesive, Light Duty, Roofing and Carbide Drill Bits.

  • Brand: Powers Fastening Innovations
  • ASIN: B00ITGCG6I
  • UPC: 075352601526

Simpson Strong Tie PHT-38 Hammer Drive tool - 1/4in barrel (1)

Simpson Strong Tie PHT-38 Hammer Drive tool -

Simpson Strong-Tie PHT-38 Hammer Drive tool - 1/4" Barrel

  • Brand: Simpson Strong-Tie
  • ASIN: B0082BKCIY
  • UPC: 707392449706

1/4" x 1" Hammer Drive Anchors/Mushroom Head/Zamac Alloy Body/Steel Zinc Nail (Carton: 100 pcs)

1/4" x 1" Hammer Drive Anchors/Mushroom Head/Zamac Alloy

Hammer Drive Anchors, 1/4" x 1" Hammer Drive Anchors / Mushroom Head / Zamac Alloy Body / Steel Zinc Nail

  • Brand: Newport Fasteners
  • ASIN: B07CYNJSVD

CONFAST 1/4" x 1-1/4" Hammer Drive Nail in Anchor (100 per Box)

CONFAST 1/4" x 1-1/4" Hammer Drive Nail in

ApplicationsThe anchor is made from ZAMAC. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Dry environment.Hole Diameter/Bit DiameterThe anchor requires a 1/4" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/4".Length Anchor The length of the anchor is 1-1/4"Minimum EmbedmentThe minimum anchor embedment into the concrete is 3/4". Therefore, the anchor must be installed so that a minimum of 3/4" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.

  • Brand: CONFAST
  • ASIN: B072QRCC85

Hard-to-Find Fastener 014973326616 Flat Hammer Drive Anchors, 1/4 x 1-1/8, Piece-50

Hard-to-Find Fastener 014973326616 Flat Hammer Drive Anchors, 1/4

We stock a wide variety of fasteners ideal for many applications around the home, farm, business, automotives, and in industry. Most of our fasteners have a light zinc plating over steel giving a more rust resistant finish. We also sell coated and stainless products for additional rust resistance. We stock many grades of fasteners ranging from low carbon steel on up to hardened, heat treated steel. Not all fasteners are applicable for all applications so be certain to test thoroughly and get the opinion of a licensed builder or certified building or structural engineer before relying on these fasteners for any situations where failure would result in damage to property or person.

  • Brand: Hard-to-Find Fastener
  • ASIN: B00L1J1NW8
  • UPC: 738287057140

Milwaukee 2767-20 M18 Fuel High Torque 1/2-Inch Impact Wrench with Friction Ring

Milwaukee 2767-20 M18 Fuel High Torque 1/2-Inch Impact

The 2767-20 M18 FUEL High Torque 1/2 inch Impact Wrench with Friction Ring eliminates the need to use a pneumatic tool for those stubborn and rusted bolts by delivering 1,000 ft-lbs of fastening torque and 1400 ft-lbs of nut-busting torque. With 2X faster removal speed, users will be able to get the job done faster and be more productive throughout their day. By providing the industry’s most compact cordless High Torque Impact Wrench at 8.39 inches length, this tool allows for more access in tight spaces. 4-Mode DRIVE CONTROL with Bolt Removal mode gives users the most control over their fasteners. Bolt Removal mode gives the user more control when removing fasteners by slowing to 750rpm once the fastener has been busted loose. This tool offers quick, tool-free socket changes with a 1/2 inch friction ring anvil. A premium rubber overmold material gives you ultimate comfort during prolonged use while lasting longer against corrosive materials.

  • Brand: Milwaukee
  • ASIN: B077H7JP1D
  • UPC: 045242502233

BOSTITCH BTFP3KIT 3-Tool Portable Air Compressor Combo Kit

BOSTITCH BTFP3KIT 3-Tool Portable Air Compressor Combo

The BOSTITCH BTFP3KIT 3-Tool Portable Air Compressor Combo Kit is ideal for interior and exterior finishing and trimming project for a variety of crafts like furniture, cabinets, and staircases. It features a 150 max PSI 6.0 gallon tank (22.7 L) and 2.6 SCFM* delivered 90 PSI pump, which enables long tool run time with quick recovery. The air compressor features long-life oil-free, maintenance-free pump for convenient use. It has a BOSTITCH high efficiency motor for easy start up in cold weather or extension cord application [14 ga or larger, 50 ft. (15.2 m) or less]. At only 78.5 dBA** operational noise level it offers you a quiet work environment. The SB-1850BN 18 GA brad nailer drives 18GA brad nails from 5/8 in. to 2 in.. SB-1664FN 16 GA straight finish nailer drives 16 GA straight finish nails from 1-1/4 in. to 2-1/2 in.. The BTFP71875 heavy-duty 3/8 in. crown stapler drives 3/8 in. crown staples from 1/4 in. to 9/16 in. and 18GA brad nails from 1/2 in. to 5/8 in.. 1/4 in. x 15' PVC air hose with fittings, along with 1-1/4 in. 18GA brad nails and 2 in. 16GA straight finish nails and T50 staples are included. Includes: 1) 6-gallon Pancake Compressor, 1) 18GA 2 in. Brad nailer, 1) 2-1/2 in. 16GA Straight Finish Nailer, 1) Heavy Duty 3/8 in. Crown Stapler, 1) 25' Air Hose, and ...

  • Color: Yellow
  • Brand: BOSTITCH
  • ASIN: B00UHNM60C
  • UPC: 719918336957

Milwaukee Electric Tools MLW2553-20 M12 Fuel 1/4" Hex Impact Driver (Bare)

Milwaukee Electric Tools MLW2553-20 M12 Fuel 1/4" Hex

Hex impact driver once again raises the bar for 12V performance with best in class driving speed, power, and size. By Focusing on productivity, this impact driver gets the job done faster by being over 20% faster in application speed vs. The competition. This tool outputs over 1, 300 in. Lbs. Of torque that allows the user to get more work done by completing a wide range of fastening. Measuring only 5.1” in length allows for unmatched access in tight spaces.

  • Brand: Milwaukee Electric Tools
  • ASIN: B077ZYMK1W
  • UPC: 045242521135

Wheeler Firearms Accurizing Torque Wrench with Inch/Pounds Measurement, Bits and Storage Case for Scope Mounting, Gunsmithing and Maintenance

Wheeler Firearms Accurizing Torque Wrench with Inch/Pounds Measurement,

Wheeler's FAT Wrench brings perfect consistency to every screw on your rifle! This amazing handheld torque wrench lets you apply repeatable, accurate torque settings to scope rings, guard screws and other screws, which aids in accuracy and decreases the opportunity for problems in the field. The FAT Wrench is a perfect complement to the Deluxe Gunsmithing Screwdriver Sets. Together, they can ensure accurate tightening of most every screw on any gun in your collection.

  • Color: Original Version
  • Brand: Wheeler
  • ASIN: B0012AXR4S
  • UPC: 768405301350

Porter-Cable PCE211 7.5 Amp 1/2" Impact Wrench

Porter-Cable PCE211 7.5 Amp 1/2" Impact

The Porter-Cable PCE211 7.5 amp 1/2" impact wrench features a 1/2" hog ring anvil for easy socket changes. The 7.5 amp motor allows for heavy duty applications, with 450 ft.lbs of torque for installing and removing heavy fasteners. 2, 200 RPM & 2, 700 BPM provide fast application speeds. This impact wrench also offers a forward/ Revers rocker switch. 120 volts. Backed by a 3 year limited warranty/1 year free service contract/90 day money back guarantee. Includes: 1) PCE211 impact wrench.

  • Brand: PORTER-CABLE
  • ASIN: B07255QCN4
  • UPC: 885911504355

DEWALT DCF887B 20V MAX XR Li-Ion Brushless 0.25" 3-Speed Impact Driver

DEWALT DCF887B 20V MAX XR Li-Ion Brushless 0.25"

The DEWALT DCF887B 20V MAX XR Li-ion Brushless 1/4" 3-Speed Impact Driver Bare tool features a DEWALT built brushless motor. This impact driver has 3-speed settings for optimized application versatility, along with Precision Drive in speed 1 for precision applications and added control. It offers three (3) LED lights with 20 second delay after trigger release to provide visibility without shadows. It also allows for one-handed loading 1/4" hex chuck with easy grip sleeve, and accepts 1" bit tips. This unit has a compact and lightweight design to fit into tight areas (2 mm shorter than the previous DCF886). Includes belt clip. This is a bare tool item - battery sold separately.

  • Brand: DEWALT
  • ASIN: B0183RLW8A
  • UPC: 885911425421
Similar Hammer Drive Fastener Results